How to Reset Service 4X4 Light on Silverado

If the Service 4×4 Light is on, it means that there is a problem with the four-wheel drive system. To reset the light, do the following:1. Put the truck in park and turn off the engine.

2. Press and hold the trip odometer reset button while turning the key to the ON position without starting the engine.3. Release the button when “Pwr” displays in the odometer window. This will put you in diagnostic mode.

4. Scroll through the menu by pressing and releasing the trip odometer reset button until “DIC” displays in the odometer window. This stands for Driver Information Center which is where you will find your Service 4×4 Light information.5. Press and releasethe trip odometer reset button once to enter DIC mode.

The message “SERVICE 4WD SYSTEM” should display along with a number next to it indicating how many times this message has been displayed since being cleared last time (if 0 then this is first time). If no message appears, or another message appears, turn off ignition and repeat steps 1-5 again until correct message appears in display window 6 . With correct message now showing press & hold trip odometer reset button again for 5 seconds or untilmessage changes & goes blank (you may haveto do this step more than once to get desired results).

Releasebutton & turn ignition off .

  • Park your Silverado on level ground and turn off the engine
  • Remove the key from the ignition and open the driver’s door
  • Locate the fuse box under the dash on the driver’s side of the Silverado
  • Find the fuse labeled “ECM-B” in the fuse box and remove it with a pair of pliers or a screwdriver
  • Insert a paperclip into each end of the removed fuse to hold it in place, then reinsert it into its slot in the fuse box firmly so that it makes good contact with both sides of its socket
  • Start your Silverado’s engine and let it idle for about five minutes, then turn it off again and remove key from ignition once more
  • Open driver’s door once more and locate small black box on top of fuse box with two wires running to it–this is your service 4×4 light reset button

Silverado Service 4×4 Light

How to Clear Service 4Wd Light

If your “Service 4WD” light is illuminated on your instrument panel, it means that there is a problem with your four-wheel drive system. This is a serious issue that should be addressed as soon as possible, as it can lead to further damage if left unaddressed. Luckily, there are a few things you can do to clear the light and get your four-wheel drive system back in working order.

First and foremost, check your owner’s manual. Many times, the service 4WD light will come on as a result of something as simple as low fluid levels. If this is the case, simply topping off the fluids should do the trick.

However, if the problem is more serious, such as a faulty sensor or actuator, then you’ll need to take your vehicle to a qualified repair shop for further diagnosis and repairs.In short, if your “Service 4WD” light is illuminated, don’t ignore it! Check your owner’s manual for possible causes and solutions, and if all else fails, take it to a professional for further assistance.

With proper care and maintenance, you can keep your four-wheel drive system running smoothly for years to come.

Silverado Service 4Wd Message

If you’re driving a Chevy Silverado, you may have seen the “Service 4WD” message on your dash. This indicates that there’s a problem with your truck’s four-wheel drive system and it needs to be serviced.There are a few different things that could be causing this message to come on.

It could be something as simple as low fluid levels in the transfer case or axle, or it could be a more serious issue like a Failed Transfer Case Encoder Motor Position Sensor (CEMPS).If you see this message, it’s best to take your truck to a qualified mechanic who can diagnose and fix the problem. Trying to drive with four-wheel drive problems can cause further damage to your truck and may even void your warranty.

Can I Still Drive With Service 4Wd Light on

If your “Service 4WD” light is on, it means that there is a problem with the four-wheel drive system in your vehicle. You should not drive your vehicle with this light on, as it could cause further damage to the system. Instead, take it to a mechanic or dealership to have it checked out and repaired.

How to Read Service 4Wd Code

If you have a four-wheel drive vehicle, it’s important to know how to read the service 4wd codes. These codes can tell you if there is a problem with your four-wheel drive system and can help you troubleshoot the issue. Here’s how to read service 4wd codes:

The first step is to find the code reader for your vehicle. This may be a handheld device that plugs into your vehicle’s diagnostic port, or it may be built into your vehicle’s infotainment system. Once you’ve located the code reader, turn on your engine and select the “4WD” option on the code reader.

Next, refer to the code chart in your owner’s manual to determine what the codes mean. The most common codes are C0035 (left front axle sensor circuit failure) and C0040 (right front axle sensor circuit failure). If you see either of these codes, it means there is a problem with one of the sensors that helps your four-wheel drive system engage properly.

If you’re not sure what a particular code means, don’t hesitate to consult with your dealer or an experienced mechanic. They’ll be able to help you diagnose the problem and get your four-wheel drive system back up and running again.

How to Reset Service 4X4 Light on Silverado

Credit: www.statestreetautoservice.com

What Does It Mean When My Silverado Says Service 4 Wheel Drive?

If you see the message “Service 4 Wheel Drive” on your Chevy Silverado, it means that there is a problem with the four-wheel drive system and it needs to be serviced. The four-wheel drive system is what allows your truck to move forward or backward on slippery or uneven surfaces by sending power to all four wheels. When there is a problem with the system, it can’t send power to all four wheels and may cause your truck to get stuck in mud or snow.

If you see this message, take your truck to a certified Chevrolet dealer for service.

Why Does My Service 4X4 Light Keep Coming On?

If your 4×4 light keeps coming on, it’s likely because there’s an issue with your transfer case. The transfer case is what sends power to the front and rear wheels, and when it isn’t working properly, the 4×4 light will come on as a warning sign.There are a few different things that could be causing your transfer case to malfunction.

It could be something as simple as a loose connection or low fluid levels. Or, it could be a more serious issue like a damaged bearing or gear.If you’re not sure what’s causing your 4×4 light to keep coming on, the best thing to do is take it to a mechanic for diagnosis.

They’ll be able to pinpoint the problem and get you back on the road in no time.

Where is the Fuse for 4 Wheel Drive in a Chevy Silverado?

Assuming you are referring to the fuse that controls the 4WD system:The fuse for the 4WD system on a Chevy Silverado is located in the engine bay. On most Silverado models, it will be located on the driver’s side, near the battery.

The exact location may vary depending on your specific model year.

What Does Service 4Wd Mean on 2014 Chevy Silverado?

Service 4WD on a 2014 Chevy Silverado means that the four-wheel drive system is not working properly and needs to be serviced. The first thing you should do if you think your four-wheel drive system is not working properly, is to check the fluid level in the transfer case. If the fluid level is low, add more fluid until it reaches the proper level.

If adding fluid does not fix the problem, then there may be an issue with the four-wheel drive system itself. You will need to take your truck to a mechanic or dealership for further diagnosis and repairs.

Conclusion

If you’re like most people, you probably don’t think much about your truck’s 4×4 system until you need it. Then, when you do need it and the light is on, it can be a little daunting. This article will show you how to reset the service 4×4 light on your Chevrolet Silverado.

It’s actually pretty simple to do, but there are a few things that you’ll need to know first. The first thing is that this procedure will only work if your truck is in 2-wheel drive mode. If it’s not, then the 4×4 system won’t engage and the light will stay on.

The second thing is that you’ll need to have access to the fuse box under the hood of your truck. Once you’ve located it, open it up and find the fuse for the 4×4 system. It should be labeled clearly.

Pull out the fuse and wait for about 30 seconds before putting it back in. That should reset the system and turn off the light.

Pin It on Pinterest

Share This
Scroll to Top