To reset the fuel filter life on a 2018 Ram 2500, first locate the fuel filter. There is a small handle on top of the filter housing that can be turned to release the housing cover. Once the cover is removed, there is a black knob on the bottom of the housing.
This knob can be turned to release the old filter. Install the new filter and turn the knob to secure it in place. Finally, put the cover back on and turn the handle to lock it in place.
- Park your Ram 2500 and set the parking brake
- Locate the fuel filter canister on the driver’s side of the vehicle, near the front of the gas tank
- Unscrew the cap from the canister and remove it
- Take out the old filter from the canister and dispose of it properly
- Insert a new filter into the canister, making sure that it is seated correctly
- Screw on the cap tightly and lower your Ram 2500 off its jack stands or ramps
- Start up your truck and check for leaks around the fuel filter canister before driving away
How To Reset Oil and Fuel Filter Service Lights on 2010-2018 Cummins 2500 & 3500 (16 Laramie 3500)
How to Reset Fuel Filter Life on 2017 Ram 2500
If you own a 2017 Ram 2500, you may be wondering how to reset the fuel filter life. The process is actually quite simple and can be done in just a few minutes. Here’s what you need to do:
1. Locate the fuel filter housing under the hood of your truck. It will be on the passenger side, near the front of the engine compartment.2. Using a ratchet and socket, loosen the housing cap until it comes off.
Be careful not to lose any of the small parts that may fall out when you remove the cap.3. Pull out the old fuel filter and discard it properly. Make sure not to touch any of the exposed surfaces as they can be quite dirty.
4. Take your new fuel filter and insert it into the housing, making sure that it is seated correctly.
How to Reset Fuel Filter Life on 2019 Ram 2500
If you own a 2019 Ram 2500, chances are you’re aware of the importance of keeping your fuel filter clean. A dirty fuel filter can lead to all sorts of problems, from decreased fuel economy to engine damage. That’s why it’s important to reset the fuel filter life indicator on your truck every time you change the filter.
Here’s how to do it:1. Start the engine and let it idle for a few minutes.2. Turn off the engine and disconnect the negative battery cable.
3. Locate the fuel filter life indicator (it will be located on the instrument panel).4. Press and hold the button for five seconds until the indicator light begins flashing.5. Reconnect the negative battery cable and start the engine.
The fuel filter life indicator should now be reset!
How to Reset Fuel Filter Life on 2020 Ram 2500
If you’re the owner of a 2020 Ram 2500, then you know that one of the most important maintenance items for your truck is the fuel filter. The fuel filter helps to remove contaminants from the fuel before it reaches the engine, and over time, it can become clogged with debris. When this happens, it’s necessary to reset the fuel filter life on your Ram 2500 so that it can continue to function properly.
Here’s how to do it:1. Start by disconnecting the negative battery cable. This will help to prevent any sparks from occurring while you’re working on the truck.
2. Next, locate the fuel filter housing under the hood of your truck. It will be located near the firewall on the driver’s side of the vehicle.3. Using a socket wrench, loosen and remove the housing cap bolts so that you can access the fuel filter inside.
4. Carefully remove the old fuel filter from its housing and discard it properly. Then, take a moment to inspect the housing for any dirt or debris buildup that could potentially damage your new filter – if there is anything present, clean it out before proceeding further.
How to Reset Fuel Filter Message on 2019 Ram 3500
If you’re driving a 2019 Ram 3500, you may have noticed a message on your dash that says “Fuel Filter.” This is actually a maintenance reminder, and it’s telling you that it’s time to replace your fuel filter. Don’t worry, this is a pretty easy process and we’ll walk you through it step by step.
First, open the hood and locate the fuel filter. It’s located under the driver’s side of the truck, near the firewall. Once you’ve found it, disconnect the negative battery cable.
This will prevent any sparks from happening when you remove the old fuel filter.Next, use a wrench to loosen the nut that secures the fuel line to the filter housing. You may need to use some force to break it loose.
Once it’s loose, carefully remove the fuel line from the housing. Take note of which way the arrow is pointing on the housing so you can put the new one in correctly.Now it’s time to install the new fuel filter.

Credit: www.homerskeltonford.com
How Do You Reset the Fuel Filter on a 2017 Ram 2500?
If you’re looking to reset the fuel filter on your 2017 Ram 2500, here’s what you’ll need to do. First, locate the fuel filter. It’s usually located near the gas tank, and it may have a cover or shield over it.
Once you’ve found it, remove the cover or shield and disconnect the fuel line from the filter. Next, use a wrench or pliers to loosen the housing nut that secures the filter in place. Once that’s loose, pull out the old filter and replace it with a new one.
Make sure to tighten the housing nut before reconnecting the fuel line. And that’s it! You’ve successfully reset your fuel filter and your Ram 2500 should be good to go.
How Do You Reset the Oil Life on a 2018 Dodge Ram 2500 Diesel?
If you need to reset the oil life on your 2018 Dodge Ram 2500 diesel, there are a few different ways that you can do so. One way is to simply turn the key to the “on” position and then press and hold the button for the odometer until it displays “oil life 100%.” You can also do this by pressing and holding the button for the trip odometer while turning the key to the “on” position.
If neither of these methods works, you may need to consult your owner’s manual for specific instructions.
How Do You Reset the Performance Service on a 2018 Ram 2500?
If you’re looking to reset the performance service on your 2018 Ram 2500, there are a few things you’ll need to do. First, you’ll need to disconnect the battery for about 30 minutes. This will allow the computer to reset itself and clear any stored codes.
Next, you’ll need to reconnect the battery and start the truck. Once it’s running, you’ll need to drive it for about 15 minutes at a speed of around 55 mph. After that, you should be good to go!
How Many Fuel Filters Does a 2018 Ram 2500 Have?
A 2018 Ram 2500 has two fuel filters. One is located in the fuel tank and the other is located under the hood, near the engine.
Conclusion
If you own a 2018 Ram 2500, you may be wondering how to reset the fuel filter life. Luckily, it’s a pretty simple process! Just follow these steps:
1. Locate the fuel filter housing under the hood of your truck.2. Unscrew the cap from the housing and remove the old filter.3. Insert the new filter into the housing and screw on the cap.
4. Start up your truck and let it idle for a few minutes to prime the new filter.5. That’s it! You’ve successfully reset your fuel filter life and are now good to go!